Commit 54e72f0b authored by Clemens Ladisch's avatar Clemens Ladisch
Browse files

ALSA: dice: reorganize interface definitions 



Move the DICE interface symbols into a separate header file, and add
more documentation.

Signed-off-by: default avatarClemens Ladisch <clemens@ladisch.de>
parent 20b65dd0

sound/firewire/dice-interface.h

0 → 100644
+371 −0
Original line number Diff line number Diff line 
#ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED

#define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED



/*

 * DICE device interface definitions

 */



/*

 * Generally, all registers can be read like memory, i.e., with quadlet read or

 * block read transactions with any alignment or length.  Writes are not

 * allowed except where noted; quadlet-sized registers must be written with

 * a quadlet write transaction.

 *

 * All values are in big endian.  The DICE firmware runs on a little-endian CPU

 * and just byte-swaps _all_ quadlets on the bus, so values without endianness

 * (e.g. strings) get scrambled and must be byte-swapped again by the driver.

 */



/*

 * Streaming is handled by the "DICE driver" interface.  Its registers are

 * located in this private address space.

 */

#define DICE_PRIVATE_SPACE		0xffffe0000000uLL



/*

 * The registers are organized in several sections, which are organized

 * separately to allow them to be extended individually.  Whether a register is

 * supported can be detected by checking its offset against its section's size.

 *

 * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/

 * size values are measured in quadlets.  Read-only.

 */

#define DICE_GLOBAL_OFFSET		0x00

#define DICE_GLOBAL_SIZE		0x04

#define DICE_TX_OFFSET			0x08

#define DICE_TX_SIZE			0x0c

#define DICE_RX_OFFSET			0x10

#define DICE_RX_SIZE			0x14

#define DICE_EXT_SYNC_OFFSET		0x18

#define DICE_EXT_SYNC_SIZE		0x1c

#define DICE_UNUSED2_OFFSET		0x20

#define DICE_UNUSED2_SIZE		0x24



/*

 * Global settings.

 */



/*

 * Stores the full 64-bit address (node ID and offset in the node's address

 * space) where the device will send notifications.  Must be changed with

 * a compare/swap transaction by the owner.  This register is automatically

 * cleared on a bus reset.

 */

#define GLOBAL_OWNER			0x000

#define  OWNER_NO_OWNER			0xffff000000000000uLL

#define  OWNER_NODE_SHIFT		48



/*

 * A bitmask with asynchronous events; read-only.  When any event(s) happen,

 * the bits of previous events are cleared, and the value of this register is

 * also written to the address stored in the owner register.

 */

#define GLOBAL_NOTIFICATION		0x008

/* Some registers in the Rx/Tx sections may have changed. */

#define  NOTIFY_RX_CFG_CHG		0x00000001

#define  NOTIFY_TX_CFG_CHG		0x00000002

/* Lock status of the current clock source may have changed. */

#define  NOTIFY_LOCK_CHG		0x00000010

/* Write to the clock select register has been finished. */

#define  NOTIFY_CLOCK_ACCEPTED		0x00000020

/* Lock status of some clock source has changed. */

#define  NOTIFY_EXT_STATUS		0x00000040

/* Other bits may be used for device-specific events. */



/*

 * A name that can be customized for each device; read/write.  Padded with zero

 * bytes.  Quadlets are byte-swapped.  The encoding is whatever the host driver

 * happens to be using.

 */

#define GLOBAL_NICK_NAME		0x00c

#define  NICK_NAME_SIZE			64



/*

 * The current sample rate and clock source; read/write.  Whether a clock

 * source or sample rate is supported is device-specific; the internal clock

 * source is always available.  Low/mid/high = up to 48/96/192 kHz.  This

 * register can be changed even while streams are running.

 */

#define GLOBAL_CLOCK_SELECT		0x04c

#define  CLOCK_SOURCE_MASK		0x000000ff

#define  CLOCK_SOURCE_AES1		0x00000000

#define  CLOCK_SOURCE_AES2		0x00000001

#define  CLOCK_SOURCE_AES3		0x00000002

#define  CLOCK_SOURCE_AES4		0x00000003

#define  CLOCK_SOURCE_AES_ANY		0x00000004

#define  CLOCK_SOURCE_ADAT		0x00000005

#define  CLOCK_SOURCE_TDIF		0x00000006

#define  CLOCK_SOURCE_WC		0x00000007

#define  CLOCK_SOURCE_ARX1		0x00000008

#define  CLOCK_SOURCE_ARX2		0x00000009

#define  CLOCK_SOURCE_ARX3		0x0000000a

#define  CLOCK_SOURCE_ARX4		0x0000000b

#define  CLOCK_SOURCE_INTERNAL		0x0000000c

#define  CLOCK_RATE_MASK		0x0000ff00

#define  CLOCK_RATE_32000		0x00000000

#define  CLOCK_RATE_44100		0x00000100

#define  CLOCK_RATE_48000		0x00000200

#define  CLOCK_RATE_88200		0x00000300

#define  CLOCK_RATE_96000		0x00000400

#define  CLOCK_RATE_176400		0x00000500

#define  CLOCK_RATE_192000		0x00000600

#define  CLOCK_RATE_ANY_LOW		0x00000700

#define  CLOCK_RATE_ANY_MID		0x00000800

#define  CLOCK_RATE_ANY_HIGH		0x00000900

#define  CLOCK_RATE_NONE		0x00000a00

#define  CLOCK_RATE_SHIFT		8



/*

 * Enable streaming; read/write.  Writing a non-zero value (re)starts all

 * streams that have a valid iso channel set; zero stops all streams.  The

 * streams' parameters must be configured before starting.  This register is

 * automatically cleared on a bus reset.

 */

#define GLOBAL_ENABLE			0x050



/*

 * Status of the sample clock; read-only.

 */

#define GLOBAL_STATUS			0x054

/* The current clock source is locked. */

#define  STATUS_SOURCE_LOCKED		0x00000001

/* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */

#define  STATUS_NOMINAL_RATE_MASK	0x0000ff00



/*

 * Status of all clock sources; read-only.

 */

#define GLOBAL_EXTENDED_STATUS		0x058

/*

 * The _LOCKED bits always show the current status; any change generates

 * a notification.

 */

#define  EXT_STATUS_AES1_LOCKED		0x00000001

#define  EXT_STATUS_AES2_LOCKED		0x00000002

#define  EXT_STATUS_AES3_LOCKED		0x00000004

#define  EXT_STATUS_AES4_LOCKED		0x00000008

#define  EXT_STATUS_ADAT_LOCKED		0x00000010

#define  EXT_STATUS_TDIF_LOCKED		0x00000020

#define  EXT_STATUS_ARX1_LOCKED		0x00000040

#define  EXT_STATUS_ARX2_LOCKED		0x00000080

#define  EXT_STATUS_ARX3_LOCKED		0x00000100

#define  EXT_STATUS_ARX4_LOCKED		0x00000200

#define  EXT_STATUS_WC_LOCKED		0x00000400

/*

 * The _SLIP bits do not generate notifications; a set bit indicates that an

 * error occurred since the last time when this register was read with

 * a quadlet read transaction.

 */

#define  EXT_STATUS_AES1_SLIP		0x00010000

#define  EXT_STATUS_AES2_SLIP		0x00020000

#define  EXT_STATUS_AES3_SLIP		0x00040000

#define  EXT_STATUS_AES4_SLIP		0x00080000

#define  EXT_STATUS_ADAT_SLIP		0x00100000

#define  EXT_STATUS_TDIF_SLIP		0x00200000

#define  EXT_STATUS_ARX1_SLIP		0x00400000

#define  EXT_STATUS_ARX2_SLIP		0x00800000

#define  EXT_STATUS_ARX3_SLIP		0x01000000

#define  EXT_STATUS_ARX4_SLIP		0x02000000

#define  EXT_STATUS_WC_SLIP		0x04000000



/*

 * The measured rate of the current clock source, in Hz; read-only.

 */

#define GLOBAL_SAMPLE_RATE		0x05c



/*

 * The version of the DICE driver specification that this device conforms to;

 * read-only.

 */

#define GLOBAL_VERSION			0x060



/* Some old firmware versions do not have the following global registers: */



/*

 * Supported sample rates and clock sources; read-only.

 */

#define GLOBAL_CLOCK_CAPABILITIES	0x064

#define  CLOCK_CAP_RATE_32000		0x00000001

#define  CLOCK_CAP_RATE_44100		0x00000002

#define  CLOCK_CAP_RATE_48000		0x00000004

#define  CLOCK_CAP_RATE_88200		0x00000008

#define  CLOCK_CAP_RATE_96000		0x00000010

#define  CLOCK_CAP_RATE_176400		0x00000020

#define  CLOCK_CAP_RATE_192000		0x00000040

#define  CLOCK_CAP_SOURCE_AES1		0x00010000

#define  CLOCK_CAP_SOURCE_AES2		0x00020000

#define  CLOCK_CAP_SOURCE_AES3		0x00040000

#define  CLOCK_CAP_SOURCE_AES4		0x00080000

#define  CLOCK_CAP_SOURCE_AES_ANY	0x00100000

#define  CLOCK_CAP_SOURCE_ADAT		0x00200000

#define  CLOCK_CAP_SOURCE_TDIF		0x00400000

#define  CLOCK_CAP_SOURCE_WC		0x00800000

#define  CLOCK_CAP_SOURCE_ARX1		0x01000000

#define  CLOCK_CAP_SOURCE_ARX2		0x02000000

#define  CLOCK_CAP_SOURCE_ARX3		0x04000000

#define  CLOCK_CAP_SOURCE_ARX4		0x08000000

#define  CLOCK_CAP_SOURCE_INTERNAL	0x10000000



/*

 * Names of all clock sources; read-only.  Quadlets are byte-swapped.  Names

 * are separated with one backslash, the list is terminated with two

 * backslashes.  Unused clock sources are included.

 */

#define GLOBAL_CLOCK_SOURCE_NAMES	0x068

#define  CLOCK_SOURCE_NAMES_SIZE	256



/*

 * Capture stream settings.  This section includes the number/size registers

 * and the registers of all streams.

 */



/*

 * The number of supported capture streams; read-only.

 */

#define TX_NUMBER			0x000



/*

 * The size of one stream's register block, in quadlets; read-only.  The

 * registers of the first stream follow immediately afterwards; the registers

 * of the following streams are offset by this register's value.

 */

#define TX_SIZE				0x004



/*

 * The isochronous channel number on which packets are sent, or -1 if the

 * stream is not to be used; read/write.

 */

#define TX_ISOCHRONOUS			0x008



/*

 * The number of audio channels; read-only.  There will be one quadlet per

 * channel; the first channel is the first quadlet in a data block.

 */

#define TX_NUMBER_AUDIO			0x00c



/*

 * The number of MIDI ports, 0-8; read-only.  If > 0, there will be one

 * additional quadlet in each data block, following the audio quadlets.

 */

#define TX_NUMBER_MIDI			0x010



/*

 * The speed at which the packets are sent, SCODE_100-_400; read/write.

 */

#define TX_SPEED			0x014



/*

 * Names of all audio channels; read-only.  Quadlets are byte-swapped.  Names

 * are separated with one backslash, the list is terminated with two

 * backslashes.

 */

#define TX_NAMES			0x018

#define  TX_NAMES_SIZE			256



/*

 * Audio IEC60958 capabilities; read-only.  Bitmask with one bit per audio

 * channel.

 */

#define TX_AC3_CAPABILITIES		0x118



/*

 * Send audio data with IEC60958 label; read/write.  Bitmask with one bit per

 * audio channel.  This register can be changed even while the stream is

 * running.

 */

#define TX_AC3_ENABLE			0x11c



/*

 * Playback stream settings.  This section includes the number/size registers

 * and the registers of all streams.

 */



/*

 * The number of supported playback streams; read-only.

 */

#define RX_NUMBER			0x000



/*

 * The size of one stream's register block, in quadlets; read-only.  The

 * registers of the first stream follow immediately afterwards; the registers

 * of the following streams are offset by this register's value.

 */

#define RX_SIZE				0x004



/*

 * The isochronous channel number on which packets are received, or -1 if the

 * stream is not to be used; read/write.

 */

#define RX_ISOCHRONOUS			0x008



/*

 * Index of first quadlet to be interpreted; read/write.  If > 0, that many

 * quadlets at the beginning of each data block will be ignored, and all the

 * audio and MIDI quadlets will follow.

 */

#define RX_SEQ_START			0x00c



/*

 * The number of audio channels; read-only.  There will be one quadlet per

 * channel.

 */

#define RX_NUMBER_AUDIO			0x010



/*

 * The number of MIDI ports, 0-8; read-only.  If > 0, there will be one

 * additional quadlet in each data block, following the audio quadlets.

 */

#define RX_NUMBER_MIDI			0x014



/*

 * Names of all audio channels; read-only.  Quadlets are byte-swapped.  Names

 * are separated with one backslash, the list is terminated with two

 * backslashes.

 */

#define RX_NAMES			0x018

#define  RX_NAMES_SIZE			256



/*

 * Audio IEC60958 capabilities; read-only.  Bitmask with one bit per audio

 * channel.

 */

#define RX_AC3_CAPABILITIES		0x118



/*

 * Receive audio data with IEC60958 label; read/write.  Bitmask with one bit

 * per audio channel.  This register can be changed even while the stream is

 * running.

 */

#define RX_AC3_ENABLE			0x11c



/*

 * Extended synchronization information.

 * This section can be read completely with a block read request.

 */



/*

 * Current clock source; read-only.

 */

#define EXT_SYNC_CLOCK_SOURCE		0x000



/*

 * Clock source is locked (boolean); read-only.

 */

#define EXT_SYNC_LOCKED			0x004



/*

 * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or

 * _NONE; read-only.

 */

#define EXT_SYNC_RATE			0x008



/*

 * ADAT user data bits; read-only.

 */

#define EXT_SYNC_ADAT_USER_DATA		0x00c

/* The data bits, if available. */

#define  ADAT_USER_DATA_MASK		0x0f

/* The data bits are not available. */

#define  ADAT_USER_DATA_NO_DATA		0x10



#endif

sound/firewire/dice.c

+2 −207
Original line number Diff line number Diff line
@@ -26,212 +26,7 @@ 
#include "amdtp.h"

#include "iso-resources.h"

#include "lib.h"



#define DICE_PRIVATE_SPACE		0xffffe0000000uLL



/* offset from DICE_PRIVATE_SPACE; offsets and sizes in quadlets */

#define DICE_GLOBAL_OFFSET		0x00

#define DICE_GLOBAL_SIZE		0x04

#define DICE_TX_OFFSET			0x08

#define DICE_TX_SIZE			0x0c

#define DICE_RX_OFFSET			0x10

#define DICE_RX_SIZE			0x14



/* pointed to by DICE_GLOBAL_OFFSET */

#define GLOBAL_OWNER			0x000

#define  OWNER_NO_OWNER			0xffff000000000000uLL

#define  OWNER_NODE_SHIFT		48

#define GLOBAL_NOTIFICATION		0x008

#define  NOTIFY_RX_CFG_CHG		0x00000001

#define  NOTIFY_TX_CFG_CHG		0x00000002

#define  NOTIFY_DUP_ISOC		0x00000004

#define  NOTIFY_BW_ERR			0x00000008

#define  NOTIFY_LOCK_CHG		0x00000010

#define  NOTIFY_CLOCK_ACCEPTED		0x00000020

#define  NOTIFY_INTERFACE_CHG		0x00000040

#define  NOTIFY_MESSAGE			0x00100000

#define GLOBAL_NICK_NAME		0x00c

#define  NICK_NAME_SIZE			64

#define GLOBAL_CLOCK_SELECT		0x04c

#define  CLOCK_SOURCE_MASK		0x000000ff

#define  CLOCK_SOURCE_AES1		0x00000000

#define  CLOCK_SOURCE_AES2		0x00000001

#define  CLOCK_SOURCE_AES3		0x00000002

#define  CLOCK_SOURCE_AES4		0x00000003

#define  CLOCK_SOURCE_AES_ANY		0x00000004

#define  CLOCK_SOURCE_ADAT		0x00000005

#define  CLOCK_SOURCE_TDIF		0x00000006

#define  CLOCK_SOURCE_WC		0x00000007

#define  CLOCK_SOURCE_ARX1		0x00000008

#define  CLOCK_SOURCE_ARX2		0x00000009

#define  CLOCK_SOURCE_ARX3		0x0000000a

#define  CLOCK_SOURCE_ARX4		0x0000000b

#define  CLOCK_SOURCE_INTERNAL		0x0000000c

#define  CLOCK_RATE_MASK		0x0000ff00

#define  CLOCK_RATE_32000		0x00000000

#define  CLOCK_RATE_44100		0x00000100

#define  CLOCK_RATE_48000		0x00000200

#define  CLOCK_RATE_88200		0x00000300

#define  CLOCK_RATE_96000		0x00000400

#define  CLOCK_RATE_176400		0x00000500

#define  CLOCK_RATE_192000		0x00000600

#define  CLOCK_RATE_ANY_LOW		0x00000700

#define  CLOCK_RATE_ANY_MID		0x00000800

#define  CLOCK_RATE_ANY_HIGH		0x00000900

#define  CLOCK_RATE_NONE		0x00000a00

#define  CLOCK_RATE_SHIFT		8

#define GLOBAL_ENABLE			0x050

#define  ENABLE				0x00000001

#define GLOBAL_STATUS			0x054

#define  STATUS_SOURCE_LOCKED		0x00000001

#define  STATUS_RATE_CONFLICT		0x00000002

#define  STATUS_NOMINAL_RATE_MASK	0x0000ff00

#define GLOBAL_EXTENDED_STATUS		0x058

#define  EXT_STATUS_AES1_LOCKED		0x00000001

#define  EXT_STATUS_AES2_LOCKED		0x00000002

#define  EXT_STATUS_AES3_LOCKED		0x00000004

#define  EXT_STATUS_AES4_LOCKED		0x00000008

#define  EXT_STATUS_ADAT_LOCKED		0x00000010

#define  EXT_STATUS_TDIF_LOCKED		0x00000020

#define  EXT_STATUS_ARX1_LOCKED		0x00000040

#define  EXT_STATUS_ARX2_LOCKED		0x00000080

#define  EXT_STATUS_ARX3_LOCKED		0x00000100

#define  EXT_STATUS_ARX4_LOCKED		0x00000200

#define  EXT_STATUS_WC_LOCKED		0x00000400

#define  EXT_STATUS_AES1_SLIP		0x00010000

#define  EXT_STATUS_AES2_SLIP		0x00020000

#define  EXT_STATUS_AES3_SLIP		0x00040000

#define  EXT_STATUS_AES4_SLIP		0x00080000

#define  EXT_STATUS_ADAT_SLIP		0x00100000

#define  EXT_STATUS_TDIF_SLIP		0x00200000

#define  EXT_STATUS_ARX1_SLIP		0x00400000

#define  EXT_STATUS_ARX2_SLIP		0x00800000

#define  EXT_STATUS_ARX3_SLIP		0x01000000

#define  EXT_STATUS_ARX4_SLIP		0x02000000

#define  EXT_STATUS_WC_SLIP		0x04000000

#define GLOBAL_SAMPLE_RATE		0x05c

#define GLOBAL_VERSION			0x060

#define GLOBAL_CLOCK_CAPABILITIES	0x064

#define  CLOCK_CAP_RATE_32000		0x00000001

#define  CLOCK_CAP_RATE_44100		0x00000002

#define  CLOCK_CAP_RATE_48000		0x00000004

#define  CLOCK_CAP_RATE_88200		0x00000008

#define  CLOCK_CAP_RATE_96000		0x00000010

#define  CLOCK_CAP_RATE_176400		0x00000020

#define  CLOCK_CAP_RATE_192000		0x00000040

#define  CLOCK_CAP_SOURCE_AES1		0x00010000

#define  CLOCK_CAP_SOURCE_AES2		0x00020000

#define  CLOCK_CAP_SOURCE_AES3		0x00040000

#define  CLOCK_CAP_SOURCE_AES4		0x00080000

#define  CLOCK_CAP_SOURCE_AES_ANY	0x00100000

#define  CLOCK_CAP_SOURCE_ADAT		0x00200000

#define  CLOCK_CAP_SOURCE_TDIF		0x00400000

#define  CLOCK_CAP_SOURCE_WC		0x00800000

#define  CLOCK_CAP_SOURCE_ARX1		0x01000000

#define  CLOCK_CAP_SOURCE_ARX2		0x02000000

#define  CLOCK_CAP_SOURCE_ARX3		0x04000000

#define  CLOCK_CAP_SOURCE_ARX4		0x08000000

#define  CLOCK_CAP_SOURCE_INTERNAL	0x10000000

#define GLOBAL_CLOCK_SOURCE_NAMES	0x068

#define  CLOCK_SOURCE_NAMES_SIZE	256



/* pointed to by DICE_TX_OFFSET */

#define TX_NUMBER			0x000

#define TX_SIZE				0x004

/* repeated TX_NUMBER times, offset by TX_SIZE quadlets */

#define TX_ISOCHRONOUS			0x008

#define TX_NUMBER_AUDIO			0x00c

#define TX_NUMBER_MIDI			0x010

#define TX_SPEED			0x014

#define TX_NAMES			0x018

#define  TX_NAMES_SIZE			256

#define TX_AC3_CAPABILITIES		0x118

#define TX_AC3_ENABLE			0x11c



/* pointed to by DICE_RX_OFFSET */

#define RX_NUMBER			0x000

#define RX_SIZE				0x004

/* repeated RX_NUMBER times, offset by RX_SIZE quadlets */

#define RX_ISOCHRONOUS			0x008

#define RX_SEQ_START			0x00c

#define RX_NUMBER_AUDIO			0x010

#define RX_NUMBER_MIDI			0x014

#define RX_NAMES			0x018

#define  RX_NAMES_SIZE			256

#define RX_AC3_CAPABILITIES		0x118

#define RX_AC3_ENABLE			0x11c





#define FIRMWARE_LOAD_SPACE		0xffffe0100000uLL



/* offset from FIRMWARE_LOAD_SPACE */

#define FIRMWARE_VERSION		0x000

#define FIRMWARE_OPCODE			0x004

#define  OPCODE_MASK			0x00000fff

#define  OPCODE_GET_IMAGE_DESC		0x00000000

#define  OPCODE_DELETE_IMAGE		0x00000001

#define  OPCODE_CREATE_IMAGE		0x00000002

#define  OPCODE_UPLOAD			0x00000003

#define  OPCODE_UPLOAD_STAT		0x00000004

#define  OPCODE_RESET_IMAGE		0x00000005

#define  OPCODE_TEST_ACTION		0x00000006

#define  OPCODE_GET_RUNNING_IMAGE_VINFO	0x0000000a

#define  OPCODE_EXECUTE			0x80000000

#define FIRMWARE_RETURN_STATUS		0x008

#define FIRMWARE_PROGRESS		0x00c

#define  PROGRESS_CURR_MASK		0x00000fff

#define  PROGRESS_MAX_MASK		0x00fff000

#define  PROGRESS_TOUT_MASK		0x0f000000

#define  PROGRESS_FLAG			0x80000000

#define FIRMWARE_CAPABILITIES		0x010

#define  FL_CAP_AUTOERASE		0x00000001

#define  FL_CAP_PROGRESS		0x00000002

#define FIRMWARE_DATA			0x02c

#define  TEST_CMD_POKE			0x00000001

#define  TEST_CMD_PEEK			0x00000002

#define  CMD_GET_AVS_CNT		0x00000003

#define  CMD_CLR_AVS_CNT		0x00000004

#define  CMD_SET_MODE			0x00000005

#define  CMD_SET_MIDIBP			0x00000006

#define  CMD_GET_AVSPHASE		0x00000007

#define  CMD_ENABLE_BNC_SYNC		0x00000008

#define  CMD_PULSE_BNC_SYNC		0x00000009

#define  CMD_EMUL_SLOW_CMD		0x0000000a

#define FIRMWARE_TEST_DELAY		0xfd8

#define FIRMWARE_TEST_BUF		0xfdc





/* EAP */

#define EAP_PRIVATE_SPACE		0xffffe0200000uLL



#define EAP_CAPABILITY_OFFSET		0x000

#define EAP_CAPABILITY_SIZE		0x004

/* ... */



#define EAP_ROUTER_CAPS			0x000

#define  ROUTER_EXPOSED			0x00000001

#define  ROUTER_READ_ONLY		0x00000002

#define  ROUTER_FLASH			0x00000004

#define  MAX_ROUTES_MASK		0xffff0000

#define EAP_MIXER_CAPS			0x004

#define  MIXER_EXPOSED			0x00000001

#define  MIXER_READ_ONLY		0x00000002

#define  MIXER_FLASH			0x00000004

#define  MIXER_IN_DEV_MASK		0x000000f0

#define  MIXER_OUT_DEV_MASK		0x00000f00

#define  MIXER_INPUTS_MASK		0x00ff0000

#define  MIXER_OUTPUTS_MASK		0xff000000

#define EAP_GENERAL_CAPS		0x008

#define  GENERAL_STREAM_CONFIG		0x00000001

#define  GENERAL_FLASH			0x00000002

#define  GENERAL_PEAK			0x00000004

#define  GENERAL_MAX_TX_STREAMS_MASK	0x000000f0

#define  GENERAL_MAX_RX_STREAMS_MASK	0x00000f00

#define  GENERAL_STREAM_CONFIG_FLASH	0x00001000

#define  GENERAL_CHIP_MASK		0x00ff0000

#define  GENERAL_CHIP_DICE_II		0x00000000

#define  GENERAL_CHIP_DICE_MINI		0x00010000

#define  GENERAL_CHIP_DICE_JR		0x00020000

#include "dice-interface.h"





struct dice {
@@ -479,7 +274,7 @@ static int dice_enable_set(struct dice *dice) 
	__be32 value;

	int rcode, err, errors = 0;



	value = cpu_to_be32(ENABLE);

	value = cpu_to_be32(1);

	for (;;) {

		rcode = fw_run_transaction(device->card,

					   TCODE_WRITE_QUADLET_REQUEST,