Loading Documentation/dmatest.txt +3 −3 Original line number Diff line number Diff line Loading @@ -34,7 +34,7 @@ command: After a while you will start to get messages about current status or error like in the original code. Note that running a new test will stop any in progress test. Note that running a new test will not stop any in progress test. The following command should return actual state of the test. % cat /sys/kernel/debug/dmatest/run Loading @@ -52,8 +52,8 @@ To wait for test done the user may perform a busy loop that checks the state. The module parameters that is supplied to the kernel command line will be used for the first performed test. After user gets a control, the test could be interrupted or re-run with same or different parameters. For the details see the above section "Part 2 - When dmatest is built as a module..." re-run with the same or different parameters. For the details see the above section "Part 2 - When dmatest is built as a module..." In both cases the module parameters are used as initial values for the test case. You always could check them at run-time by running Loading Documentation/filesystems/xfs.txt +3 −0 Original line number Diff line number Diff line Loading @@ -33,6 +33,9 @@ When mounting an XFS filesystem, the following options are accepted. removing extended attributes) the on-disk superblock feature bit field will be updated to reflect this format being in use. CRC enabled filesystems always use the attr2 format, and so will reject the noattr2 mount option if it is set. barrier Enables the use of block layer write barriers for writes into the journal and unwritten extent conversion. This allows for Loading MAINTAINERS +11 −1 Original line number Diff line number Diff line Loading @@ -2890,8 +2890,8 @@ F: drivers/media/dvb-frontends/ec100* ECRYPT FILE SYSTEM M: Tyler Hicks <tyhicks@canonical.com> M: Dustin Kirkland <dustin.kirkland@gazzang.com> L: ecryptfs@vger.kernel.org W: http://ecryptfs.org W: https://launchpad.net/ecryptfs S: Supported F: Documentation/filesystems/ecryptfs.txt Loading Loading @@ -4448,6 +4448,16 @@ S: Maintained F: drivers/scsi/*iscsi* F: include/scsi/*iscsi* ISCSI EXTENSIONS FOR RDMA (ISER) INITIATOR M: Or Gerlitz <ogerlitz@mellanox.com> M: Roi Dayan <roid@mellanox.com> L: linux-rdma@vger.kernel.org S: Supported W: http://www.openfabrics.org W: www.open-iscsi.org Q: http://patchwork.kernel.org/project/linux-rdma/list/ F: drivers/infiniband/ulp/iser ISDN SUBSYSTEM M: Karsten Keil <isdn@linux-pingi.de> L: isdn4linux@listserv.isdn4linux.de (subscribers-only) Loading Makefile +1 −1 Original line number Diff line number Diff line VERSION = 3 PATCHLEVEL = 10 SUBLEVEL = 0 EXTRAVERSION = -rc4 EXTRAVERSION = -rc5 NAME = Unicycling Gorilla # *DOCUMENTATION* Loading arch/arm/boot/dts/bcm2835.dtsi +1 −0 Original line number Diff line number Diff line Loading @@ -44,6 +44,7 @@ uart@20201000 { reg = <0x7e201000 0x1000>; interrupts = <2 25>; clock-frequency = <3000000>; arm,primecell-periphid = <0x00241011>; }; gpio: gpio { Loading Loading
Documentation/dmatest.txt +3 −3 Original line number Diff line number Diff line Loading @@ -34,7 +34,7 @@ command: After a while you will start to get messages about current status or error like in the original code. Note that running a new test will stop any in progress test. Note that running a new test will not stop any in progress test. The following command should return actual state of the test. % cat /sys/kernel/debug/dmatest/run Loading @@ -52,8 +52,8 @@ To wait for test done the user may perform a busy loop that checks the state. The module parameters that is supplied to the kernel command line will be used for the first performed test. After user gets a control, the test could be interrupted or re-run with same or different parameters. For the details see the above section "Part 2 - When dmatest is built as a module..." re-run with the same or different parameters. For the details see the above section "Part 2 - When dmatest is built as a module..." In both cases the module parameters are used as initial values for the test case. You always could check them at run-time by running Loading
Documentation/filesystems/xfs.txt +3 −0 Original line number Diff line number Diff line Loading @@ -33,6 +33,9 @@ When mounting an XFS filesystem, the following options are accepted. removing extended attributes) the on-disk superblock feature bit field will be updated to reflect this format being in use. CRC enabled filesystems always use the attr2 format, and so will reject the noattr2 mount option if it is set. barrier Enables the use of block layer write barriers for writes into the journal and unwritten extent conversion. This allows for Loading
MAINTAINERS +11 −1 Original line number Diff line number Diff line Loading @@ -2890,8 +2890,8 @@ F: drivers/media/dvb-frontends/ec100* ECRYPT FILE SYSTEM M: Tyler Hicks <tyhicks@canonical.com> M: Dustin Kirkland <dustin.kirkland@gazzang.com> L: ecryptfs@vger.kernel.org W: http://ecryptfs.org W: https://launchpad.net/ecryptfs S: Supported F: Documentation/filesystems/ecryptfs.txt Loading Loading @@ -4448,6 +4448,16 @@ S: Maintained F: drivers/scsi/*iscsi* F: include/scsi/*iscsi* ISCSI EXTENSIONS FOR RDMA (ISER) INITIATOR M: Or Gerlitz <ogerlitz@mellanox.com> M: Roi Dayan <roid@mellanox.com> L: linux-rdma@vger.kernel.org S: Supported W: http://www.openfabrics.org W: www.open-iscsi.org Q: http://patchwork.kernel.org/project/linux-rdma/list/ F: drivers/infiniband/ulp/iser ISDN SUBSYSTEM M: Karsten Keil <isdn@linux-pingi.de> L: isdn4linux@listserv.isdn4linux.de (subscribers-only) Loading
Makefile +1 −1 Original line number Diff line number Diff line VERSION = 3 PATCHLEVEL = 10 SUBLEVEL = 0 EXTRAVERSION = -rc4 EXTRAVERSION = -rc5 NAME = Unicycling Gorilla # *DOCUMENTATION* Loading
arch/arm/boot/dts/bcm2835.dtsi +1 −0 Original line number Diff line number Diff line Loading @@ -44,6 +44,7 @@ uart@20201000 { reg = <0x7e201000 0x1000>; interrupts = <2 25>; clock-frequency = <3000000>; arm,primecell-periphid = <0x00241011>; }; gpio: gpio { Loading