Merge series "Convert Cadence QSPI bindings to yaml" from Pratyush Yadav <p.yadav@ti.com>:

* Cadence Quad SPI controller

Required properties:

- compatible : should be one of the following:

	Generic default - "cdns,qspi-nor".

	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".

	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".

	For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".

- reg : Contains two entries, each of which is a tuple consisting of a

	physical address and length. The first entry is the address and

	length of the controller register set. The second entry is the

	address and length of the QSPI Controller data area.

- interrupts : Unit interrupt specifier for the controller interrupt.

- clocks : phandle to the Quad SPI clock.

- cdns,fifo-depth : Size of the data FIFO in words.

- cdns,fifo-width : Bus width of the data FIFO in bytes.

- cdns,trigger-address : 32-bit indirect AHB trigger address.

Optional properties:

- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.

- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch

  the read data rather than the QSPI clock. Make sure that QSPI return

  clock is populated on the board before using this property.

Optional subnodes:

Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional

custom properties:

- cdns,read-delay : Delay for read capture logic, in clock cycles

- cdns,tshsl-ns : Delay in nanoseconds for the length that the master

                  mode chip select outputs are de-asserted between

		  transactions.

- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being

                  de-activated and the activation of another.

- cdns,tchsh-ns : Delay in nanoseconds between last bit of current

                  transaction and deasserting the device chip select

		  (qspi_n_ss_out).

- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low

                  and first bit transfer.

- resets	: Must contain an entry for each entry in reset-names.

		  See ../reset/reset.txt for details.

- reset-names	: Must include either "qspi" and/or "qspi-ocp".

Example:

	qspi: spi@ff705000 {

		compatible = "cdns,qspi-nor";

		#address-cells = <1>;

		#size-cells = <0>;

		reg = <0xff705000 0x1000>,

		      <0xffa00000 0x1000>;

		interrupts = <0 151 4>;

		clocks = <&qspi_clk>;

		cdns,is-decoded-cs;

		cdns,fifo-depth = <128>;

		cdns,fifo-width = <4>;

		cdns,trigger-address = <0x00000000>;

		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;

		reset-names = "qspi", "qspi-ocp";

		flash0: n25q00@0 {

			...

			cdns,read-delay = <4>;

			cdns,tshsl-ns = <50>;

			cdns,tsd2d-ns = <50>;

			cdns,tchsh-ns = <4>;

			cdns,tslch-ns = <4>;

		};

	};

# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)

%YAML 1.2

---

$id: http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#

$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Cadence Quad SPI controller

maintainers:

  - Pratyush Yadav <p.yadav@ti.com>

allOf:

  - $ref: spi-controller.yaml#

properties:

  compatible:

    oneOf:

      - items:

          - enum:

              - ti,k2g-qspi

              - ti,am654-ospi

              - intel,lgm-qspi

          - const: cdns,qspi-nor

      - const: cdns,qspi-nor

  reg:

    items:

      - description: the controller register set

      - description: the controller data area

  interrupts:

    maxItems: 1

  clocks:

    maxItems: 1

  cdns,fifo-depth:

    description:

      Size of the data FIFO in words.

    $ref: "/schemas/types.yaml#/definitions/uint32"

    enum: [ 128, 256 ]

    default: 128

  cdns,fifo-width:

    $ref: /schemas/types.yaml#/definitions/uint32

    description:

      Bus width of the data FIFO in bytes.

    default: 4

  cdns,trigger-address:

    $ref: /schemas/types.yaml#/definitions/uint32

    description:

      32-bit indirect AHB trigger address.

  cdns,is-decoded-cs:

    type: boolean

    description:

      Flag to indicate whether decoder is used to select different chip select

      for different memory regions.

  cdns,rclk-en:

    type: boolean

    description:

      Flag to indicate that QSPI return clock is used to latch the read

      data rather than the QSPI clock. Make sure that QSPI return clock

      is populated on the board before using this property.

  resets:

    maxItems: 2

  reset-names:

    minItems: 1

    maxItems: 2

    items:

      enum: [ qspi, qspi-ocp ]

# subnode's properties

patternProperties:

  "@[0-9a-f]+$":

    type: object

    description:

      Flash device uses the below defined properties in the subnode.

    properties:

      cdns,read-delay:

        $ref: /schemas/types.yaml#/definitions/uint32

        description:

          Delay for read capture logic, in clock cycles.

      cdns,tshsl-ns:

        description:

          Delay in nanoseconds for the length that the master mode chip select

          outputs are de-asserted between transactions.

      cdns,tsd2d-ns:

        description:

          Delay in nanoseconds between one chip select being de-activated

          and the activation of another.

      cdns,tchsh-ns:

        description:

          Delay in nanoseconds between last bit of current transaction and

          deasserting the device chip select (qspi_n_ss_out).

      cdns,tslch-ns:

        description:

          Delay in nanoseconds between setting qspi_n_ss_out low and

          first bit transfer.

required:

  - compatible

  - reg

  - interrupts

  - clocks

  - cdns,fifo-depth

  - cdns,fifo-width

  - cdns,trigger-address

  - '#address-cells'

  - '#size-cells'

unevaluatedProperties: false

examples:

  - |

    qspi: spi@ff705000 {

      compatible = "cdns,qspi-nor";

      #address-cells = <1>;

      #size-cells = <0>;

      reg = <0xff705000 0x1000>,

            <0xffa00000 0x1000>;

      interrupts = <0 151 4>;

      clocks = <&qspi_clk>;

      cdns,fifo-depth = <128>;

      cdns,fifo-width = <4>;

      cdns,trigger-address = <0x00000000>;

      resets = <&rst 0x1>, <&rst 0x2>;

      reset-names = "qspi", "qspi-ocp";

      flash@0 {

              compatible = "jedec,spi-nor";

              reg = <0x0>;

      };

    };