Merge remote-tracking branches 'regulator/topic/notifier',...

  --PFUZE100

  sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6

  --PFUZE200

  sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6

  sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6,coin

  --PFUZE3000

  sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4

				regulator-max-microvolt = <3300000>;

				regulator-always-on;

			};

			coin_reg: coin {

				regulator-min-microvolt = <2500000>;

				regulator-max-microvolt = <3300000>;

				regulator-always-on;

			};

		};

	};

  design requires. This property describes the total system ramp time

  required due to the combination of internal ramping of the regulator itself,

  and board design issues such as trace capacitance and load on the supply.

- regulator-settling-time-us: Settling time, in microseconds, for voltage

  change if regulator have the constant time for any level voltage change.

  This is useful when regulator have exponential voltage change.

- regulator-soft-start: Enable soft start so that voltage ramps slowly

- regulator-state-mem sub-root node for Suspend-to-RAM mode

  : suspend to memory, the device goes to sleep, but all data stored in memory,

TPS65132 regulators

Required properties:

- compatible: "ti,tps65132"

- reg: I2C slave address

Optional Subnode:

Device supports two regulators OUTP and OUTN. A sub node within the

   device node describe the properties of these regulators. The sub-node

   names must be as follows:

	-For regulator outp, the sub node name should be "outp".

	-For regulator outn, the sub node name should be "outn".

-enable-gpios:(active high, output) Regulators are controlled by the input pins.

   If it is connected to GPIO through host system then provide the

   gpio number as per gpio.txt.

-active-discharge-gpios: (active high, output) Some configurations use delay mechanisms

  on the enable pin, to keep the regulator enabled for some time after

  the enable signal goes low. This GPIO is used to actively discharge

  the delay mechanism. Requires specification of ti,active-discharge-time-us

-ti,active-discharge-time-us: how long the active discharge gpio should be

  asserted for during active discharge, in microseconds.

Each regulator is defined using the standard binding for regulators.

Example:

	tps65132@3e {

		compatible = "ti,tps65132";

		reg = <0x3e>;

		outp {

			regulator-name = "outp";

			regulator-boot-on;

			regulator-always-on;

			enable-gpios = <&gpio 23 0>;

		};

		outn {

			regulator-name = "outn";

			regulator-boot-on;

			regulator-always-on;

			regulator-active-discharge = <0>;

			enable-gpios = <&gpio 40 0>;

		};

	};

	  This driver provides support for the voltage regulators on the

	  TI TPS65090 PMIC.

config REGULATOR_TPS65132

	tristate "TI TPS65132 Dual Output Power regulators"

	depends on I2C && GPIOLIB

	select REGMAP_I2C

	help

	  This driver supports TPS65132 single inductor - dual output

	  power supply specifcally designed for display panels.

config REGULATOR_TPS65217

	tristate "TI TPS65217 Power regulators"

	depends on MFD_TPS65217

obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o

obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o

obj-$(CONFIG_REGULATOR_TPS80031) += tps80031-regulator.o

obj-$(CONFIG_REGULATOR_TPS65132) += tps65132-regulator.o

obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o twl6030-regulator.o

obj-$(CONFIG_REGULATOR_VEXPRESS) += vexpress-regulator.o

obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o