Commit 5a4e5e6a authored by Guenter Roeck's avatar Guenter Roeck Committed by Jean Delvare
Browse files

hwmon: (lm90) Add support for ADT7461A and NCT1008 



This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.

Signed-off-by: default avatarGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
parent fafc9929

Documentation/hwmon/lm90

+17 −6
Original line number Diff line number Diff line
@@ -32,6 +32,16 @@ Supported chips: 
    Addresses scanned: I2C 0x4c and 0x4d

    Datasheet: Publicly available at the ON Semiconductor website

               http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461

  * Analog Devices ADT7461A

    Prefix: 'adt7461a'

    Addresses scanned: I2C 0x4c and 0x4d

    Datasheet: Publicly available at the ON Semiconductor website

               http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461A

  * ON Semiconductor NCT1008

    Prefix: 'nct1008'

    Addresses scanned: I2C 0x4c and 0x4d

    Datasheet: Publicly available at the ON Semiconductor website

               http://www.onsemi.com/PowerSolutions/product.do?id=NCT1008

  * Maxim MAX6646

    Prefix: 'max6646'

    Addresses scanned: I2C 0x4d
@@ -149,7 +159,7 @@ ADM1032: 
  * ALERT is triggered by open remote sensor.

  * SMBus PEC support for Write Byte and Receive Byte transactions.



ADT7461:

ADT7461, ADT7461A, NCT1008:

  * Extended temperature range (breaks compatibility)

  * Lower resolution for remote temperature
@@ -205,11 +215,12 @@ SMBus Alert Support 
This driver has basic support for SMBus alert. When an alert is received,

the status register is read and the faulty temperature channel is logged.



The Analog Devices chips (ADM1032 and ADT7461) do not implement the SMBus

alert protocol properly so additional care is needed: the ALERT output is

disabled when an alert is received, and is re-enabled only when the alarm

is gone. Otherwise the chip would block alerts from other chips in the bus

as long as the alarm is active.

The Analog Devices chips (ADM1032, ADT7461 and ADT7461A) and ON

Semiconductor chips (NCT1008) do not implement the SMBus alert protocol

properly so additional care is needed: the ALERT output is disabled when

an alert is received, and is re-enabled only when the alarm is gone.

Otherwise the chip would block alerts from other chips in the bus as long

as the alarm is active.



PEC Support

-----------

drivers/hwmon/Kconfig

+4 −4
Original line number Diff line number Diff line
@@ -618,10 +618,10 @@ config SENSORS_LM90 
	depends on I2C

	help

	  If you say yes here you get support for National Semiconductor LM90,

	  LM86, LM89 and LM99, Analog Devices ADM1032 and ADT7461, Maxim

	  MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,

	  MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, and Winbond/Nuvoton

	  W83L771W/G/AWG/ASG sensor chips.

	  LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,

	  Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,

	  MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,

	  and Winbond/Nuvoton W83L771W/G/AWG/ASG sensor chips.



	  This driver can also be built as a module.  If so, the module

	  will be called lm90.

drivers/hwmon/lm90.c

+15 −7
Original line number Diff line number Diff line
@@ -49,10 +49,10 @@ 
 * chips, but support three temperature sensors instead of two. MAX6695

 * and MAX6696 only differ in the pinout so they can be treated identically.

 *

 * This driver also supports the ADT7461 chip from Analog Devices.

 * It's supported in both compatibility and extended mode. It is mostly

 * compatible with LM90 except for a data format difference for the

 * temperature value registers.

 * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as

 * NCT1008 from ON Semiconductor. The chips are supported in both compatibility

 * and extended mode. They are mostly compatible with LM90 except for a data

 * format difference for the temperature value registers.

 *

 * Since the LM90 was the first chipset supported by this driver, most

 * comments will refer to this chipset, but are actually general and
@@ -88,9 +88,10 @@ 
 * Addresses to scan

 * Address is fully defined internally and cannot be changed except for

 * MAX6659, MAX6680 and MAX6681.

 * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, MAX6649, MAX6657,

 * MAX6658 and W83L771 have address 0x4c.

 * ADM1032-2, ADT7461-2, LM89-1, LM99-1 and MAX6646 have address 0x4d.

 * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649,

 * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c.

 * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D

 * have address 0x4d.

 * MAX6647 has address 0x4e.

 * MAX6659 can have address 0x4c, 0x4d or 0x4e.

 * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
@@ -174,6 +175,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680, 
static const struct i2c_device_id lm90_id[] = {

	{ "adm1032", adm1032 },

	{ "adt7461", adt7461 },

	{ "adt7461a", adt7461 },

	{ "lm90", lm90 },

	{ "lm86", lm86 },

	{ "lm89", lm86 },
@@ -188,6 +190,7 @@ static const struct i2c_device_id lm90_id[] = { 
	{ "max6681", max6680 },

	{ "max6695", max6696 },

	{ "max6696", max6696 },

	{ "nct1008", adt7461 },

	{ "w83l771", w83l771 },

	{ }

};
@@ -1153,6 +1156,11 @@ static int lm90_detect(struct i2c_client *new_client, 
		 && (reg_config1 & 0x1B) == 0x00

		 && reg_convrate <= 0x0A) {

			name = "adt7461";

		} else

		if (chip_id == 0x57 /* ADT7461A, NCT1008 */

		 && (reg_config1 & 0x1B) == 0x00

		 && reg_convrate <= 0x0A) {

			name = "adt7461a";

		}

	} else

	if (man_id == 0x4D) { /* Maxim */