Merge drm/drm-next into drm-intel-gt-next (16d69a89) · Commits · EulixOS / Software / Kernel

Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml

+63 −2

Original line number	Original line	Diff line number	Diff line
	@@ -43,14 +43,70 @@ properties:
	vdd33-supply:		vdd33-supply:
	description: Regulator that provides the supply 3.3V power.		description: Regulator that provides the supply 3.3V power.

			analogix,lane0-swing:
			$ref: /schemas/types.yaml#/definitions/uint8-array
			minItems: 1
			maxItems: 20
			description:
			an array of swing register setting for DP tx lane0 PHY.
			Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
			Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
			Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and
			[Swing control] setting.
			Registers 0~9, bit 3:0 is [Boost control], these bits control
			post cursor manual, increase the [Boost control] to increase
			Pre-emphasis value.
			Registers 0~9, bit 6:4 is [Swing control], these bits control
			swing manual, increase [Swing control] setting to add Vp-p value
			for each Swing, Pre.
			Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
			Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
			Swing1_Pre2, Swing0_Pre3, they are for [R select control] and
			[R Termination control] setting.
			Registers 10~19, bit 4:0 is [R select control], these bits are
			compensation manual, increase it can enhance IO driven strength
			and Vp-p.
			Registers 10~19, bit 5:6 is [R termination control], these bits
			adjust 50ohm impedance of DP tx termination. 00:55 ohm,
			01:50 ohm(default), 10:45 ohm, 11:40 ohm.

			analogix,lane1-swing:
			$ref: /schemas/types.yaml#/definitions/uint8-array
			minItems: 1
			maxItems: 20
			description:
			an array of swing register setting for DP tx lane1 PHY.
			DP TX lane1 swing register setting same with lane0
			swing, please refer lane0-swing property description.

			analogix,audio-enable:
			type: boolean
			description: let the driver enable audio HDMI codec function or not.

	ports:		ports:
	$ref: /schemas/graph.yaml#/properties/ports		$ref: /schemas/graph.yaml#/properties/ports

	properties:		properties:
	port@0:		port@0:
	$ref: /schemas/graph.yaml#/properties/port		$ref: /schemas/graph.yaml#/$defs/port-base
			unevaluatedProperties: false
	description:		description:
	Video port for MIPI DSI input.		MIPI DSI/DPI input.

			properties:
			endpoint:
			$ref: /schemas/media/video-interfaces.yaml#
			type: object
			additionalProperties: false

			properties:
			remote-endpoint: true

			bus-type:
			enum: [1, 5]
			default: 1

			data-lanes: true

	port@1:		port@1:
	$ref: /schemas/graph.yaml#/properties/port		$ref: /schemas/graph.yaml#/properties/port
	@@ -87,6 +143,9 @@ examples:
	vdd10-supply = <&pp1000_mipibrdg>;		vdd10-supply = <&pp1000_mipibrdg>;
	vdd18-supply = <&pp1800_mipibrdg>;		vdd18-supply = <&pp1800_mipibrdg>;
	vdd33-supply = <&pp3300_mipibrdg>;		vdd33-supply = <&pp3300_mipibrdg>;
			analogix,audio-enable;
			analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;
			analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;

	ports {		ports {
	#address-cells = <1>;		#address-cells = <1>;
	@@ -96,6 +155,8 @@ examples:
	reg = <0>;		reg = <0>;
	anx7625_in: endpoint {		anx7625_in: endpoint {
	remote-endpoint = <&mipi_dsi>;		remote-endpoint = <&mipi_dsi>;
			bus-type = <5>;
			data-lanes = <0 1 2 3>;
	};		};
	};		};

Documentation/devicetree/bindings/display/bridge/nxp,ptn3460.yaml

0 → 100644

+106 −0

Original line number	Original line	Diff line number	Diff line
			# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
			%YAML 1.2
			---
			$id: http://devicetree.org/schemas/display/bridge/nxp,ptn3460.yaml#
			$schema: http://devicetree.org/meta-schemas/core.yaml#

			title: NXP PTN3460 eDP to LVDS bridge

			maintainers:
			- Sean Paul <seanpaul@chromium.org>

			properties:
			compatible:
			const: nxp,ptn3460

			reg:
			description: I2C address of the bridge
			maxItems: 1

			edid-emulation:
			$ref: "/schemas/types.yaml#/definitions/uint32"
			description:
			The EDID emulation entry to use
			Value Resolution Description
			0 1024x768 NXP Generic
			1 1920x1080 NXP Generic
			2 1920x1080 NXP Generic
			3 1600x900 Samsung LTM200KT
			4 1920x1080 Samsung LTM230HT
			5 1366x768 NXP Generic
			6 1600x900 ChiMei M215HGE
			enum: [0, 1, 2, 3, 4, 5, 6]

			powerdown-gpios:
			description: GPIO connected to the PD_N signal.
			maxItems: 1

			reset-gpios:
			description: GPIO connected to the RST_N signal.
			maxItems: 1

			ports:
			$ref: /schemas/graph.yaml#/properties/ports

			properties:
			port@0:
			$ref: /schemas/graph.yaml#/properties/port
			description:
			Video port for LVDS output

			port@1:
			$ref: /schemas/graph.yaml#/properties/port
			description:
			Video port for eDP input

			required:
			- port@0
			- port@1

			required:
			- compatible
			- reg
			- edid-emulation
			- powerdown-gpios
			- reset-gpios
			- ports

			additionalProperties: false

			examples:
			- \|
			#include <dt-bindings/gpio/gpio.h>

			i2c1 {
			#address-cells = <1>;
			#size-cells = <0>;

			bridge@20 {
			compatible = "nxp,ptn3460";
			reg = <0x20>;
			edid-emulation = <5>;
			powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
			reset-gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;

			ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
			reg = <0>;
			bridge_out: endpoint {
			remote-endpoint = <&panel_in>;
			};
			};

			port@1 {
			reg = <1>;
			bridge_in: endpoint {
			remote-endpoint = <&dp_out>;
			};
			};
			};
			};
			};

			...

Documentation/devicetree/bindings/display/bridge/ptn3460.txt

deleted100644 → 0

+0 −39

Original line number	Original line	Diff line number	Diff line
	ptn3460 bridge bindings

	Required properties:
	- compatible: "nxp,ptn3460"
	- reg: i2c address of the bridge
	- powerdown-gpio: OF device-tree gpio specification for PD_N pin.
	- reset-gpio: OF device-tree gpio specification for RST_N pin.
	- edid-emulation: The EDID emulation entry to use
	+-------+------------+------------------+
	\| Value \| Resolution \| Description \|
	\| 0 \| 1024x768 \| NXP Generic \|
	\| 1 \| 1920x1080 \| NXP Generic \|
	\| 2 \| 1920x1080 \| NXP Generic \|
	\| 3 \| 1600x900 \| Samsung LTM200KT \|
	\| 4 \| 1920x1080 \| Samsung LTM230HT \|
	\| 5 \| 1366x768 \| NXP Generic \|
	\| 6 \| 1600x900 \| ChiMei M215HGE \|
	+-------+------------+------------------+

	- video interfaces: Device node can contain video interface port
	nodes for panel according to [1].

	[1]: Documentation/devicetree/bindings/media/video-interfaces.txt

	Example:
	lvds-bridge@20 {
	compatible = "nxp,ptn3460";
	reg = <0x20>;
	powerdown-gpio = <&gpy2 5 1 0 0>;
	reset-gpio = <&gpx1 5 1 0 0>;
	edid-emulation = <5>;
	ports {
	port@0 {
	bridge_out: endpoint {
	remote-endpoint = <&panel_in>;
	};
	};
	};
	};

Documentation/devicetree/bindings/display/bridge/sii9234.txt

deleted100644 → 0

+0 −49

Original line number	Original line	Diff line number	Diff line
	Silicon Image SiI9234 HDMI/MHL bridge bindings

	Required properties:
	- compatible : "sil,sii9234".
	- reg : I2C address for TPI interface, use 0x39
	- avcc33-supply : MHL/USB Switch Supply Voltage (3.3V)
	- iovcc18-supply : I/O Supply Voltage (1.8V)
	- avcc12-supply : TMDS Analog Supply Voltage (1.2V)
	- cvcc12-supply : Digital Core Supply Voltage (1.2V)
	- interrupts: interrupt specifier of INT pin
	- reset-gpios: gpio specifier of RESET pin (active low)
	- video interfaces: Device node can contain two video interface port
	nodes for HDMI encoder and connector according to [1].
	- port@0 - MHL to HDMI
	- port@1 - MHL to connector

	[1]: Documentation/devicetree/bindings/media/video-interfaces.txt


	Example:
	sii9234@39 {
	compatible = "sil,sii9234";
	reg = <0x39>;
	avcc33-supply = <&vcc33mhl>;
	iovcc18-supply = <&vcc18mhl>;
	avcc12-supply = <&vsil12>;
	cvcc12-supply = <&vsil12>;
	reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
	interrupt-parent = <&gpf3>;
	interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	mhl_to_hdmi: endpoint {
	remote-endpoint = <&hdmi_to_mhl>;
	};
	};
	port@1 {
	reg = <1>;
	mhl_to_connector: endpoint {
	remote-endpoint = <&connector_to_mhl>;
	};
	};
	};
	};

Documentation/devicetree/bindings/display/bridge/sil,sii9234.yaml

0 → 100644

+110 −0

Original line number	Original line	Diff line number	Diff line
			# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
			%YAML 1.2
			---
			$id: http://devicetree.org/schemas/display/bridge/sil,sii9234.yaml#
			$schema: http://devicetree.org/meta-schemas/core.yaml#

			title: Silicon Image SiI9234 HDMI/MHL bridge

			maintainers:
			- Maciej Purski <m.purski@samsung.com>

			properties:
			compatible:
			const: sil,sii9234

			reg:
			description: I2C address for TPI interface
			maxItems: 1

			avcc12-supply:
			description: TMDS Analog Supply Voltage, 1.2V

			avcc33-supply:
			description: MHL/USB Switch Supply Voltage, 3.3V

			cvcc12-supply:
			description: Digital Core Supply Voltage, 1.2V

			iovcc18-supply:
			description: I/O voltage supply, 1.8V

			interrupts:
			maxItems: 1

			reset-gpios:
			description: GPIO connected to the reset pin.
			maxItems: 1

			ports:
			$ref: /schemas/graph.yaml#/properties/ports

			properties:
			port@0:
			$ref: /schemas/graph.yaml#/properties/port
			description:
			Video port for HDMI (encoder) input

			port@1:
			$ref: /schemas/graph.yaml#/properties/port
			description:
			MHL to connector port

			required:
			- port@0

			required:
			- compatible
			- reg
			- avcc12-supply
			- avcc33-supply
			- cvcc12-supply
			- iovcc18-supply
			- interrupts
			- reset-gpios
			- ports

			additionalProperties: false

			examples:
			- \|
			#include <dt-bindings/gpio/gpio.h>
			#include <dt-bindings/interrupt-controller/irq.h>

			i2c1 {
			#address-cells = <1>;
			#size-cells = <0>;

			bridge@39 {
			compatible = "sil,sii9234";
			reg = <0x39>;
			avcc12-supply = <&vsil12>;
			avcc33-supply = <&vcc33mhl>;
			cvcc12-supply = <&vsil12>;
			iovcc18-supply = <&vcc18mhl>;
			interrupt-parent = <&gpf3>;
			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
			reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;

			ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
			reg = <0>;
			mhl_to_hdmi: endpoint {
			remote-endpoint = <&hdmi_to_mhl>;
			};
			};

			port@1 {
			reg = <1>;
			mhl_to_connector: endpoint {
			remote-endpoint = <&connector_to_mhl>;
			};
			};
			};
			};
			};

			...